| |
| CODE |
DESCRIPTION |
Units |
| IBS737.25 |
Drill Bit, Dia. 2.5 |
2 |
| IBS737.35 |
Drill Bit, Dia. 3.5 |
2 |
| IBS700 |
Counter Sink for 3.5, 4.0mm Screw (6.0 Head) |
1 |
| IBS760.35 |
Cortical Tap for 3.5mm screws |
|
| IBS760.40 |
Cancellous Tap for 4.0mm screws, 3.5mm screws 1 each |
|
| IBS765 |
Quick Coupling handle |
|
| IBS715 |
Tap sleeve, 3.5mm diameter/drill sleeve 2.5mm diameter |
|
| IBS720 |
Insert sleeve diameter 3.5mm/2.7mm |
1 |
| IBS747 |
Small Screwdriver |
1 |
| IBS745 |
Small Screwdriver insert, 2.5mm hex., with quick coupling end |
1 |
| IBS709 |
Small depth gauge |
1 |
| IBS777.05 |
Neutral and load drill guide, 3.5mm |
1 |
| General Instruments |
| REH1053 |
Sharp Hook |
1 |
| IBS758 |
Holding clip for plates |
2 |
| IBS753 |
Self-Holding screw forceps |
1 |
| IBP630.01 |
Bending iron for small DCP, 1 of each |
2 |
|
Bending templates, 5 and 7 holes, 1 of each |
2 |
| BHF 1246.19 |
Self Centering bone holding Forceps |
1 |
| BHF 1248.14 |
Reduction forceps with points |
1 |
| BHF 1247.14 |
Reduction forceps for small fragments |
1 |
| REH1005.10 |
Small retractor, 6 and 8mm width, 1 of each |
2 |
|
Retractor for small fragments, with broad shank long |
2 |
| REH1052.06 |
Small periosteal elevator, with straight edge, 6mm width |
1 |
| IMPLANTS |
| 735.10 to 735.42 |
Small cortex screws, diameter 3.5/1.25mm |
52 |
|
(4 each of 10, 12, 14, 16, 18, 20, 22, 24, 26, 28, 32, 36, 40mm) |
|
| 725.10 to 725.60 |
Small Cancellous bone screws with full length thread, 3.5mm diam. |
30 |
|
(2 each of 14, 16, 18, 20, 22, 24, 26, 28, 30, 35, 40, 45, 50mm) |
|
| 729.10 to 729.60 |
Small Cancellous bone screws, short thread, 4.0mm diam. |
28 |
|
(2 each of 12, 14, 16, 18, 20, 22, 24, 26, 28, 30, 35, 40, 45, 50) |
|
| 760 |
Small washers for 4.0mm screws |
6 |
| 636.02 to 636.08 |
One third tubular plates, 1 each with 2, 3, 7, and 8 holes (2 each with 4, 5 and 6 holes) |
10 |
| 614.06, 614.08 & 614.10 |
Dynamic compression plates DCP 3.5mm, (2 each with 6 and 8 holes 1 with 10 holes) |
|
| 638.03 & 638.04 |
Small T-plates right angle, 1 each with 3 and 4 holes in the head |
2 |
| 622.03 & 622.04 |
Small T-plates, oblique angle, 1 each of with 3 and holes in the shaft |
2 |
| PS911.015 to PS911.020 |
Kirschner wires, 10 each of 1.25/1.6/2.0 mm diam, length 150mm |
|
|
Square Nail Impactor |
3 |
| KSN69 |
Square Nail Reamer |
5 |
|
|
